Icynene Blown-In Insulation in Henderson: What to Know First
We provide independent Icynene blown-in insulation for Henderson homes, and most attic top-up jobs with proper air sealing run one full day, with the written scope and price in your hands before any work starts. Blower-door readings are taken before and after on applicable jobs, so you see the actual change in air loss rather than a vague promise. You should know our pricing posture up front: most Henderson attic jobs land between $1,600 and $4,200 depending on square footage, current R-value, and how much old material has to come out first. Call (844) 320-5338 and a live person answers.

This page is for homeowners who already have Icynene in the house (attic cap, dense-pack wall cavity, or a hybrid install) and need to add or refresh blown-in material around it. We’re an independent Icynene service provider, not affiliated with or authorized by the manufacturer.
How Icynene Products Fail – and How We Fix Them
Icynene is a brand family, not a single product, and the failure modes depend on which line is in your home. These are the cases we run into most in Henderson attics.
- MD-R Series (spray foam) settling against blown material. In older Henderson installs, MD-R was sprayed along the attic floor, then loose cellulose was blown over it later. The two materials shrink and settle at different rates, and a gap opens along the top plates where the foam pulled back. We find these gaps during air sealing first, then re-blow to the correct settled depth instead of topping up over a hidden leak.
- Classic and MD-C open-cell foam shrinking in the desert thermal cycle. Henderson’s attic temperatures swing from 40s at night to 140-plus degrees in summer, and thin open-cell foam applied in the 2000s has often pulled away from the sheathing. The symptom is a cool ceiling in one room and a hot one next door. We measure depth and inspect the bond line before deciding whether re-blowing over it is safe or the foam needs remediation first.
- Icynene product that was never the whole story. Plenty of Henderson homes have a partial Icynene coat on the walls but bare fiberglass batts in the ceiling. The owner assumes the whole envelope is done. We map what’s actually installed room by room and explain what a top-up buys you versus a full wall retrofit. No pressure, just the map.
- Dense-pack wall cavities with Icynene as a vapor boundary. When Icynene was used on the inside face of exterior walls and dense-pack was added behind it, the key question is whether the vapor path is intact. A wrong sequence creates moisture issues in Henderson’s dry season that show up two winters later. We confirm the assembly before blowing into the cavity.
- Contamination and rodent nesting on top of old Icynene caps. Icynene’s texture traps rodent nesting material differently from straight fiberglass. When we find droppings or compressed contaminated material, we remove and dispose of the affected section per code, air seal the newly exposed framing, then re-blow with clean material.
Our Icynene Blown-In Insulation Process

- 1
Diagnostic visit and written scope. We measure current R-value in every attic zone, map what’s Icynene versus other materials, and take a blower-door reading of the home’s baseline air leakage. Under Haven Standard Clause 1, you get a flat written price, written scope, and written warranty before anyone lifts a tool.
- 2
Air-seal first, always. Top plates, can lights, penetrations, and the gap above the Icynene foam get sealed. We don’t blow insulation over an unsealed attic floor. That rule stands regardless of which brand the new material is.
- 3
Material decision. Depending on the cavity, the existing Icynene bond, and the target R-value, we specify cellulose, fiberglass, or dense-pack using product from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, or GreenFiber. No proprietary lock-in.
- 4
Blow or dense-pack. Loose fill goes down at controlled density and the depth is marked on the rafters. Dense-pack goes in wall cavities to spec density so it doesn’t settle below target.
- 5
Post-work test. On applicable jobs, the second blower-door reading is taken and printed. You’ll see the before-and-after CFM50 number on the paperwork.
- 6
Cleanup and the record. Documented Photo Record on every visit, plus your blower-door numbers and warranty in hand before we leave. The 365-Day Done Right Promise backs the work if anything’s off.
What Icynene Blown-In Insulation Costs in Henderson
These are the ranges we see in Henderson for common scenarios. Your written price will be exact before work starts.
| Scenario | Typical range |
|---|---|
| Attic top-up with air sealing, existing Icynene cap intact | $1,600 – $2,900 |
| Air sealing + top-up where Icynene has settled or pulled away | $2,200 – $3,600 |
| Dense-pack wall cavity with Icynene boundary check | $1,900 – $3,400 |
| Contaminated Icynene section removal + re-blow | $900 – $2,600 |
| Blower-door test before and after (added to a job) | $250 – $450 |
What moves the price: attic square footage, target R-value, how much material gets removed, and whether the existing Icynene foam is intact enough to leave in place. Bring a competing written estimate and we’ll read it with you at no charge.
Why Henderson Homeowners Call Envelope Insulation Henderson for Icynene Work

Three things show up in the reviews that matter most: the written price up front, the before-and-after blower-door numbers, and the photo record. Every job since 2016 has ended with a documented record and been backed by the 365-Day Done Right Promise. That’s 9,000-plus homes sealed and insulated, and we’ve never blown insulation over an unsealed attic floor. Our technicians have up to 10 years of experience with Icynene, Demilec, and Reflectix systems alongside standard blown-in work, and they’re background-checked and uniformed. Live person answers a call 24/7, no voicemail. If you’ve got a written estimate from someone else, we’ll give you a free second opinion on it.
FAQs
Not if the work is done correctly. Topping up blown-in material over an intact Icynene cap doesn’t void the manufacturer’s warranty on the existing foam as long as air sealing is done first and no moisture barrier is compromised. We document the existing assembly in the photo record so you have proof the install was done right if Icynene ever needs to be inspected. Call (844) 320-5338 for a free walk-through and estimate.
Repairing (air sealing plus a top-up) usually costs less than full removal and re-insulation, and it works when the existing Icynene is intact. Full removal makes more sense when the foam has separated from the sheathing, or contamination is present. Our written estimate lays out both options with dollar numbers. Call (844) 320-5338 for a free second opinion on any competing written estimate.
Yes. We source from Icynene, Demilec, Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, and GreenFiber, and the material specified in your written scope is the material we install. We don’t lock you into a single manufacturer, so the choice is driven by what the cavity actually needs.
Most Henderson Icynene blown-in jobs get scheduled within a few business days, and the diagnostic and written estimate usually happen on the same visit. Call (844) 320-5338 and a live person will get you on the schedule.
Yes, on applicable jobs. The blower-door test – a pressurization reading that shows in one number how much air the envelope is losing – is taken before and after the work. The two readings print on your job record so you can see the change you paid for.
Written by the team at Envelope Insulation Henderson, serving Henderson and nearby areas.