Demilec Insulation Removal & Replacement in Henderson: What to Know First
We provide independent Demilec insulation removal and replacement in Henderson, and most attic jobs run one to two days from removal to final blower-door reading. We publish a written price before any work starts, and we won’t blow new insulation until the attic floor is air-sealed. The honest part: Demilec spray foam that’s bonded well often doesn’t need full removal, and we’ll tell you which situation you’re in before you commit to a number.

This page is for Henderson homeowners who already have a Demilec product in the building envelope, whether that’s open-cell Heatlok in an attic deck or a closed-cell application in a crawl space, and who now have a reason to suspect it’s failing. Call (844) 320-5338 and a live person answers, day or night.
How Demilec Products Fail – and How We Fix Them
Demilec makes good foam. The failures we see in Henderson are almost never “the product was bad.” They’re application failures, moisture problems, or the wrong foam for the assembly, and each one calls for a different removal strategy. Here’s what actually shows up:
- Heatlok Soya and Heatlok HFO Pro applied over a damp deck. Open-cell foam is vapor-permeable, and when it’s sprayed onto sheathing that’s holding moisture, the foam traps that moisture against the wood. You get soft, crumbly foam at the rafters and staining on the decking beneath. We cut out the affected sections, dry the assembly, and replace to the same thickness rather than topping it, because new foam over wet foam just seals the problem in.
- Closed-cell Sealection 500 that pulled away from the framing. Sealection 500 adheres hard when the substrate is clean. On dusty, oily, or previously-treated lumber it can delaminate and leave a gap behind the foam. That gap becomes the air path, and your blower-door number barely improves no matter how thick the foam is. We find the disbonded areas with a probe and a thermal pass, remove the loose foam, prep the surface, and re-spray.
- Foam sprayed too thin and read as “installed.” A common one in Henderson attics: the crew sprayed a nominal 2 inches of Heatlok when the spec called for more, and the R-value never matched the sticker. If the foam is intact and clean, we can often add thickness. If it’s the wrong product for the location, removal is the answer.
- Crawl-space foam with a moisture source behind it. Demilec in a vented crawl space over bare soil is asking for trouble. The foam goes musty and starts to detach from the joists. We remove the failed material, encapsulate with a proper vapor barrier first, then re-insulate. The barrier goes down before the foam goes back up, not after.
- Vermiculite or old insulation buried under a Demilec application. We pull samples and handle any suspect vermiculite as a separate removal before foam work begins. That’s a different job with different containment, and it gets priced and scheduled on its own.
One detail Demilec’s own site won’t tell you: Heatlok HFO Pro and Sealection 500 have different removal profiles. HFO Pro is tougher to cut cleanly because the blowing agent produces a denser cell structure, so it takes a slower removal pass and more vacuum time to keep the attic clean. We plan the day around that.
Our Demilec Insulation Removal & Replacement Process

- 1
Diagnostic visit and written price. We inspect the assembly, take photos, and where it applies, run a blower-door test – a pressurization reading that shows in one number how much air the envelope is losing. You get a flat written price, scope, and warranty before anyone lifts a tool.
- 2
Containment and removal. Negative air and HEPA filtration go up before cutting. We remove the Demilec down to the substrate, bag it, and haul it out. No foam dust left in the living space.
- 3
Assembly repair. Damp sheathing, delaminated substrate, or a missing vapor barrier gets fixed before new material goes in. Skipping this step is how the next foam job fails.
- 4
Air sealing first. Top plates, can lights, and penetrations get sealed before any insulation is added. This is the step that moves your number.
- 5
Replacement and verification. New Demilec goes in to spec, or we recommend an alternate material if the assembly calls for it. We re-run the blower door and publish the before-and-after figures.
- 6
Photo record and guarantee. You get a Documented Photo Record of the whole job and the 365-Day Done Right Promise in writing. If it’s not done right, we make it right.
What Demilec Insulation Removal & Replacement Costs in Henderson
These are real ranges for Henderson homes. Most attic jobs come in at the middle of the band; crawl spaces and contaminated material run higher.
| Scenario | Typical range |
|---|---|
| Attic Demilec removal + air sealing + re-insulation (1,200 – 1,600 sq ft) | $3,400 – $6,200 |
| Partial removal and re-spray of delaminated Sealection 500 | $1,800 – $3,600 |
| Closed-cell removal from a crawl space with encapsulation | $4,500 – $8,000 |
| Vermiculite or suspect-material removal (handled separately) | $2,500 – $6,500 |
What moves the price: square footage, how much foam is disbonded versus intact, whether vermiculite is present, and how much assembly repair the decking needs. Every job gets a free estimate with the number on paper before work starts, and we’ll read a competing estimate with you at no cost.

Why Henderson Homeowners Call Envelope Insulation Henderson for Demilec Work

We’ve sealed and insulated 9,000+ homes since 2016, and every one closed with a written price and a documented record. We treat Demilec as one option among several, not the only one, so our recommendation is based on what your assembly needs. We source from Demilec, Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, and GreenFiber. If a Reflectix radiant barrier is already installed or in your plans, we work around it rather than through it. Our technicians have up to 10 years of experience, they’re background-checked and uniformed, and the 365-Day Done Right Promise backs every completed job. As an independent Demilec service provider, we’re not affiliated with or authorized by the manufacturer, and we’ll say so plainly.
FAQs
Removal by itself doesn’t void a Demilec warranty, but a sloppy reinstallation can. If your replacement foam is installed to spec by a qualified applicator, the new application carries its own coverage. We document the removal and reinstall with photos so you have a record either way. Call (844) 320-5338 and we’ll walk through your warranty paperwork with you.
Yes. We source Heatlok Soya, Heatlok HFO Pro, and Sealection 500 directly, so the replacement matches what’s already in your assembly. If a different material is the better call for the assembly, we’ll show you why before you commit.
Repair is usually cheaper when the foam is intact over at least 70 percent of the area and the problem is localized. If the disbonding runs across the whole assembly or vermiculite is underneath, full removal is the better spend. We’ll tell you which side of that line you’re on during the diagnostic.
Most Henderson diagnostic visits are scheduled within a week, and full removal and replacement jobs typically run one to two days on site. Call (844) 320-5338 for a free estimate and we’ll give you the real timeline for your address.
Yes, and we treat it as a separate scope. Suspect vermiculite gets its own containment, sampling, and removal before any foam work resumes, and it’s priced on its own line so you know exactly what you’re paying for.
Call (844) 320-5338 for a free estimate on your Demilec insulation removal and replacement in Henderson. You’ll get a written price, a photo record, and before-and-after blower-door numbers so you can see the change you paid for.
Written by the team at Envelope Insulation Henderson, serving Henderson and nearby areas.