Demilec Home Energy Audit in Henderson: What to Know First
An independent Demilec home energy audit in Henderson usually takes two to four hours and ends with a written report, blower-door readings, and thermal images you keep. Expect a diagnostic visit in the $300 to $550 range, credited toward any sealing or insulation work you approve. We’re an independent Demilec service provider, not affiliated with or authorized by Demilec, and we put a flat written price in front of you before any work starts.

This page is for Henderson homeowners whose homes already have Demilec spray foam in the attic, walls, or rim joists and who need to know whether it’s performing. If your home was built or retrofitted between 2015 and 2025, there’s a good chance Demilec foam is part of the envelope. Call (844) 320-5338 and a live person picks up.
How Demilec Products Fail – and How We Fix Them
Spray foam is sold as a permanent product, and mostly it is. But “permanent” and “performing” aren’t the same thing. Here’s what we actually find on Demilec jobs in Henderson, and what we do about each one.
- Shrink-back at the top plates (Heatlok HFO and Soya-based lines). Foam applied too thin in one pass, or onto a cold or dusty deck, can pull away from the framing over time. The gap is small, often a quarter-inch, but at Henderson summer temperatures a quarter-inch gap around every top plate adds up to a measurable CFM50 increase on the blower door. Our fix is two-part: air seal the exposed gap with a rated sealant, then bring the foam back to full depth so the thermal boundary is continuous again.
- Off-ratio or under-cured foam (mostly in older two-component installs). When the A and B sides are mixed off ratio, the foam goes brittle and crumbly instead of tough. You’ll find it dusty and friable when you press on it. Off-ratio foam has lost most of its insulating value and needs removal and replacement, not a patch. We confirm with a core sample before we quote.
- Foam over an unsealed attic floor. This is the one that costs Henderson homeowners the most. Someone foamed the roof deck or the attic floor without sealing the can lights, top plates, and wire penetrations first. The foam looks fine. The house still leaks. We run the blower door, find the bypasses, and seal them before we touch the foam.
- Rim joist foam that didn’t reach the sill plate. In Henderson’s stucco-and-frame construction, rim joists are a common cold spot and a common foam shortfall. If the foam stopped short of the sill, the joint is still open to outside air. We fill it properly and document the before-and-after with thermal imaging.
- Foam and duct leakage treated as one problem. Demilec foam on a duct chase doesn’t seal the ducts inside it. We run a duct leakage test separately. A lot of “the foam didn’t work” complaints are actually leaking flex duct run through a hot Henderson attic.
Our Demilec Home Energy Audit Process

Here’s what a Demilec audit looks like from the first call to the moment we leave.
- 1
Pre-visit intake. We ask which Demilec product was installed, where, and when, and whether you have the original contractor’s paperwork. If you don’t, we note it and inspect visually.
- 2
Baseline blower-door test. A pressurization reading that shows, in one number, how much air your building envelope is losing. This is your starting CFM50 figure and it goes in the report.
- 3
Thermal imaging and visual inspection. We photograph the foam at the top plates, rim joists, and any penetrations. Infrared shows where the foam is thin or has separated. Every image is saved to your Documented Photo Record.
- 4
Duct leakage test. Run separately from the envelope test so the two results don’t get confused. A house can pass the envelope test and still lose 20% of its conditioned air through leaking ducts.
- 5
Written scope and price. Before any repair work, you get a flat written price, a written scope, and a written warranty, per Haven Standard Clause 1. If a competitor gave you an estimate, bring it and we’ll read it with you at no charge.
- 6
Repair, re-test, and record. After sealing and any foam repair, we re-run the blower door and publish the new reading alongside the old one. You see the change you paid for, in one figure.
What Demilec Home Energy Audit Costs in Henderson
Henderson pricing depends less on square footage than on how many separate tests and repairs your house needs. Here’s what we typically quote.
| Service | Typical range |
|---|---|
| Standard home energy audit (blower door, thermal imaging, visual) | $300 – $550 |
| Audit plus duct leakage test | $450 – $750 |
| Targeted air sealing at top plates, can lights, penetrations | $600 – $1,400 |
| Foam repair or top-up (per area, e.g. rim joists) | $400 – $1,200 |
| Full foam removal and replacement (off-ratio or failed foam) | $2,500 – $6,500 |
What moves the price: the number of penetrations, whether foam has to come out, how accessible the attic is, and whether you need duct remediation on top of envelope work. An audit is credited toward approved work. Estimates are free and you get a written price before anything starts.
Why Henderson Homeowners Call Envelope Insulation Henderson for Demilec Work

Our technicians have up to 10 years of experience with spray foam and building-envelope diagnostics. They know Demilec lines from the foam itself, not just the label on the drum. We’re independently owned and operated under The Haven Standard, 9,000+ homes sealed and insulated since 2016, every one with a written price before work started and a documented record when the crew left.
We carry materials from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber, so there’s no product lock-in. If your job needs Reflectix radiant barrier as part of the fix, we source it. If a competitor’s estimate is on the table, our Free Second Opinion reads it with you. The 365-Day Done Right Promise backs every job: if it’s not done right, we make it right. Calls get answered by a live person, 24/7, and our technicians are background-checked and uniformed.
FAQs
Not if it’s done by a qualified contractor using compatible materials. Demilec’s foam warranty covers the product itself, and repairs that follow manufacturer spec don’t void it. What can void coverage is an unqualified patch using incompatible foam or sealant. We document every repair with photos and material specs so you have a record.
It depends on why it failed. Shrink-back and thin spots can usually be repaired and topped up. Off-ratio or brittle foam is a different story and generally needs removal and replacement, because the foam has lost its insulating value throughout. Our audit confirms which you have with a core sample, and the written report tells you which way we’d go.
Most audits get scheduled within a few business days, and we tell you the window when we book. If you have a known foam failure or a moisture problem, tell the person on the phone and we’ll prioritize it. Calls are answered by a live person, 24/7.
Yes, and especially if the foam went in before 2020. The audit tells you whether the foam is actually where it needs to be, whether the attic floor was sealed first, and whether your ducts are leaking. On the jobs we run in Henderson, we regularly find air bypasses under foam that the original installer never addressed.
Yes, on every applicable job. You see the CFM50 reading before we start and after we finish, on the same report. It’s the one number that shows what changed. Call (844) 320-5338 for a free estimate.
Book Your Demilec Home Energy Audit

If you have Demilec foam in your Henderson home and you’re not sure it’s doing its job, start with an audit and get real numbers. We’ll show you the blower-door reading, the thermal images, and what we’d do, in writing, before any work starts. Call (844) 320-5338 for a free estimate. A live person answers, day or night.
Written by the team at Envelope Insulation Henderson, serving Henderson and nearby areas.