Demilec Vapor Barrier Installation: The Henderson Owner’s Guide
We install Demilec-compatible vapor barrier systems throughout Henderson, and most residential crawl space and slab-edge jobs run $1,400 to $4,200 installed, depending on square footage and soil conditions. Installation is scheduled after a written price is in hand, and many jobs wrap in a single day. Envelope Insulation Henderson is an independent service provider and is not affiliated with Demilec.

Owners usually find the failure the same way: a musty smell climbing from the crawl space into the living room, or a section of poly that has pulled loose from the foundation wall. In Henderson’s older neighborhoods, the discovery often comes after a wet winter. A homeowner pulls a storage bin from under the house and finds the plastic rucked up, taped seams peeled back, and bare soil exposed. By then, the barrier has usually been failing for a season or two.
Key Takeaways:
- Demilec-compatible vapor barrier installation in Henderson: typically $1,400 to $4,200 installed.
- Failed seams and pulled fasteners are the most common failure points.
- We don’t carry parts on a truck; materials are sourced per job from Demilec and listed equivalents.
- Most installations are completed in one day, with a documented photo record on the way out.
Which Demilec Models This Applies To
Demilec’s vapor barrier products are specified by mil thickness and roll dimensions rather than a single “model number,” which is where most homeowners get stuck. The relevant spec is printed on the factory carton: look for the mil rating (typically 6, 10, or 20 mil for crawl space work), the roll width (usually 12 or 16 feet), and the product family name. Demilec’s poly products are commonly sold under their branded series, and the carton will also list the compatible seam tape and fastener systems. If your existing barrier was installed under a Demilec-branded crawl space system, the tape and mastic are as important as the plastic itself.
For the OEM-versus-aftermarket decision: Demilec’s own barrier stock and the equivalent 10-mil or 20-mil reinforced poly sold by other manufacturers perform within the same realistic range when the seams and fasteners are done correctly. We don’t insist on Demilec-branded material when an equivalent is a better fit for the job. What we won’t do is substitute a 6-mil product for a 10-mil spec to shave the price. The spec on the carton is what gets installed. If you’re matching an existing system in a Henderson home, bring us the carton label or a photo of the barrier edge, and we can confirm the correct mil and roll width before ordering.
Signs Your Demilec Vapor Barrier Installation Is Failing

- Musty odor in the crawl space or ground floor. A barrier that has lost its seal lets soil moisture rise directly into the framing. The smell is the moisture, not the plastic.
- Peeled or lifted seam tape. In Henderson’s summer heat, adhesive-backed seam tape softens and lifts. Once a seam opens, the barrier stops acting as a continuous sheet.
- Rucked, pooled, or torn barrier sections. Water intrusion or rodents push the plastic off the soil and wad it into piles. Those pooled areas let moisture back through.
- Pulled fasteners at the foundation wall. The barrier’s mechanical attachment at the wall ledge loosens as the wood dries and shifts. A gap there defeats the whole assembly.
- Bare soil visible from the access hatch. Any uncovered soil is an open moisture path. Even a small exposed patch in a Henderson crawl space will feed humid air into the home above.
Replacement Cost & What’s Included
Installed pricing for a Demilec-compatible vapor barrier in Henderson breaks down like this:
| Scope | Typical Installed Range |
|---|---|
| Standard crawl space barrier (10-mil, seams taped, wall edges fastened) | $1,400 – $2,600 |
| Heavy-duty barrier (20-mil, full perimeter fastening, mastic sealing) | $2,200 – $3,400 |
| Barrier plus minor rodent proofing or debris removal | $2,800 – $4,200 |
The range is driven by square footage, access difficulty, existing debris, and whether the wall fastening and seam tape system need to be rebuilt from scratch. The installed price includes the barrier material, seam tape, fasteners, and labor. Material cost for a typical Henderson crawl space runs $400 to $900 of that total; the rest is labor and prep. Every job starts with a written price and closes with a documented photo record, and the 365-Day Done Right Promise covers the installation work itself.

DIY or Call Us?

The crawl space is not a high-voltage hazard the way a panel is, but it’s not a safe weekend project for most people. Crawl spaces under Henderson homes can be 18 inches deep, filled with debris, and harbor rodents and sharp fasteners. A rolled 20-mil barrier weighs too much for one person to position alone, and a barrier that isn’t sealed at every seam is barely better than nothing.
What you can safely check: the carton label for mil spec, the visible condition of seam tape, and whether bare soil shows through the access hatch. What goes wrong with DIY is the seam work: the tape lifts within one summer, and the wall-edge fasteners pull without the proper anchor. If you’ve found a failure, call (844) 320-5338 for a free estimate. We’ll confirm the spec and give you a written price before we touch anything.
FAQs
A properly installed 10-mil or 20-mil barrier lasts 15 to 25 years when seams are taped with the correct tape and the wall edges are mechanically fastened. In Henderson, the summer heat is the main enemy of adhesive tape, so taped seams are the first thing to inspect. Call (844) 320-5338 for an estimate if yours is showing age.
Sometimes. If the barrier is intact and only a local seam or wall edge has failed, a spot repair is often enough. If the failure covers more than a small area, or the barrier is pulled off the soil entirely, replacement usually costs less than repeated repairs. Call (844) 320-5338 and we’ll tell you which one your job is.
Most residential Demilec-compatible vapor barrier installations in Henderson are completed in one day, and smaller crawl spaces are done in half a day. Larger homes or jobs with debris removal may run into a second day. Call (844) 320-5338 to schedule a visit.
We order by the spec printed on your existing barrier or from the carton label: mil thickness, roll width, and compatible tape and fastener system. We source Demilec material and quality equivalents from named manufacturers, and we don’t add a proprietary lock-in fee. Call (844) 320-5338 with your spec and we’ll confirm the right material before ordering.
If you’ve found a failing vapor barrier in your Henderson home, call (844) 320-5338 for a free estimate. Our technicians have up to 10 years of experience, every job starts with a written price, and you’ll get a documented photo record when we finish. We also service Reflectix barriers and can answer spec questions on either product.
Written by the team at Envelope Insulation Henderson, serving Henderson and nearby areas.