Demilec Attic Insulation: The Henderson Owner’s Guide
We install Demilec-compatible attic insulation systems across Henderson, and most full attic jobs run between $1,800 and $4,500 installed, depending on square footage, existing insulation condition, and how much air sealing the attic floor needs first. A failing Demilec installation usually shows itself the same way: a room that never gets comfortable, a monthly power bill that climbed without explanation, or insulation that looks sunken and crusty at the joist lines. Homeowners in Henderson typically find us after a hot summer pushed the electric bill up two or three hundred dollars and a neighbor mentioned their attic looked thin.

Key Takeaways
- We install Demilec-compatible insulation, seal the attic floor first, and publish before-and-after blower-door numbers on every applicable job.
- Attic insulation work in Henderson generally falls between $1,800 and $4,500.
- We’re an independent service provider. We’re not affiliated with Demilec.
- Every visit includes a written price before work starts and a Documented Photo Record when we leave.
Which Demilec Models This Applies To
Demilec (now part of the Huntsman Building Solutions family) makes spray foam systems under several series names, and the insulation in your attic could be any of them. The two you’ll run into most in Henderson homes built between 2015 and 2025 are the Heatlok HFO line and the Sealection series. Heatlok is a closed-cell foam, typically installed at around 2 to 3 inches in an attic floor or roof deck. Sealection is open-cell, usually blown in thicker. Soya-based and Classic formulas also turn up in older installs.
To identify what you have, look at three things: the label on the foam drum or the installer’s paperwork (which many homeowners keep in a closing binder), a small sample of the foam itself, and its measured density. Closed-cell is rigid and dense; open-cell is softer and lighter. If you can’t find the paperwork, the density test and a call to us will tell you what you’re working with.
On the OEM-versus-aftermarket question, the decision is different for foam than for a part like a garage spring. Demilec foam is installed as a mixed two-component liquid, so there’s no “part” to swap. What matters is that the replacement material meets the same spec for your application. We source from Demilec and from Icynene, Owens Corning, Johns Manville, Knauf, CertainTeed and GreenFiber, so you’re never locked into one product name. If your installer’s bid insists only a specific proprietary product will work, ask why. Bring us the written estimate and we’ll read it with you.
Signs Your Demilec Attic Insulation Is Failing

Foam insulation doesn’t so much wear out as get installed wrong or get damaged after the fact. Here’s what we look for, and what each symptom usually means.
- Blown or powdery spots on the closed-cell foam. That’s often a sign the two components were mixed off-ratio at the gun, which weakens the foam. Improper ratio foam cures brittle and crumbly instead of firm.
- R-value measured below the installer’s claim. A blower-door test and thermography together can show where the insulation isn’t performing to spec. If the recorded R-value is short of what you paid for, that’s the conversation to have.
- Cold spots and drafts in winter, hot rooms in summer. Foam insulation is only as good as the air sealing beneath it. If the attic floor was never sealed – top plates, can lights, penetrations – the foam is sitting over a leaking deck.
- Pests and moisture at the foam edge. Rodents tunnel through soft open-cell foam, and in Henderson’s summer monsoon humidity, foam that traps moisture against the roof sheathing can grow mold. Look for staining or a musty smell before you walk into the attic.
- Sunken or separated coverage at the perimeter. Foam that pulled away from the top plate or shrunk back from the eaves means the seal at the most important area is broken. That thin edge is where most Henderson heat gain enters.
Replacement Cost & What’s Included
For a Henderson attic that needs failed insulation removed and replaced, most jobs land between $1,800 and $4,500. The range is driven by attic square footage, the existing R-value and how easily it comes out, the depth of new insulation, whether the attic floor needs air sealing first, and whether any framing repair is needed. We price the parts and the labor on the written estimate as line items, so you can see what you’re paying for the material and what you’re paying for the install.
Every job includes a written scope and written warranty before anyone lifts a tool (Haven Standard Clause 1), plus a Documented Photo Record of the before-and-after attic. On jobs where air sealing is part of the work, we provide before-and-after blower-door readings so you can see the number that changed. Our 365-Day Done Right Promise applies to the completed work – if it’s not done right, we make it right.
DIY or Call Us?

There are things you can check safely in a Henderson attic: walk the perimeter with a flashlight, look for the sunken foam and staining, and find the installation paperwork. What we’d tell you not to do is pull a sample of the foam yourself or attempt to repair a foam-covered area without knowing what’s underneath. Foam installs use two-part chemistry and a heated proportioner; a re-foam job without proper equipment leaves you with a stronger-looking mess than the original. If you smell a chemical odor or see damaged or delaminating foam, stop and call us at (844) 320-5338.
For the insulation work itself, the routine is: a free second opinion if you have a competing bid, a written price before any work starts, sealed attic floor first, then new insulation, then a blower-door reading to show the change. Live person on the phone 24/7, background-checked technicians, and a text when they’re on the way.
FAQs
Closed-cell spray foam properly installed under a sealed deck should hold its R-value for decades; open-cell foam is typically rated for 25 to 30 years before performance drops. In Henderson’s climate, the bigger variable is moisture and pest intrusion, not foam age. If you see staining, soft spots or pest tunneling, treat it sooner.
Often yes, if the failure is localized. A patched area of foam, sealant at the perimeter and re-check with a blower-door can restore performance for well under the cost of a full replacement. If the foam was badly mixed or the coverage is thin across the whole attic, replacement is the better call. We’ll tell you which one your attic needs after we look, and put it in a written price.
Most attic insulation jobs run one to two days from arrival to final blower-door reading, depending on square footage and how much existing material has to come out. Smaller partial replacements can finish in a single day. We’ll give you the timeline with the written price before anyone starts.
We buy Demilec and equivalent materials from the manufacturer and from Owens Corning, Icynene, Johns Manville, Knauf, CertainTeed and GreenFiber. We don’t lock you into one product name, and we don’t claim exclusive status with any brand. We confirm the right spec for your attic and application on the written scope. For a Reflectix radiant barrier question, we handle that too.
Ready to see what your attic is actually losing? Call Envelope Insulation Henderson at (844) 320-5338 for a free estimate. We’ll bring the flashlight, the written price and the blower door – and you’ll walk away with the numbers, not a handshake.
Written by the team at Envelope Insulation Henderson, serving Henderson and nearby areas.