A Topside company - serving Henderson, NV

Icynene Attic Insulation in Henderson, NV

Icynene Attic Insulation: The Henderson Owner’s Guide

We install Icynene-compatible attic insulation in Henderson, and most full attic jobs here run between $2,400 and $6,800 installed, depending on square footage, existing insulation, and how much air sealing the attic floor needs first. Same-day and next-day scheduling is usually available. Owners typically discover a problem after a summer power bill jumps $80 to $150 in one billing cycle, or after they walk into a garage that’s hotter than the driveway. Softer signs come first: rooms that won’t hold temperature, a faint chemical or musty smell near the attic hatch, and insulation that’s settled two or three inches below where it started.

Contractor performing residential attic insulation removal and replacement services in Henderson, NV

Call (844) 320-5338

Key takeaways

  • Icynene attic insulation in Henderson generally costs $2,400 to $6,800 installed.
  • In Henderson’s climate, the failure is usually heat and UV, not the product itself.
  • Air sealing happens before insulation. Always. That’s how we work.
  • You get a written price before any work starts, and before-and-after blower-door numbers on applicable jobs.

Which Icynene Models This Applies To

Icynene covers two families of attic product: spray foam (open-cell and closed-cell, including the classic Icynene LD-C-50 water-blown open-cell line and its successors) and the blown-in loose-fill and blanket products that go under the Icynene brand through licensed manufacturers. Which one you have changes what “replacement” means. Spray foam that’s failing usually gets removed and re-applied; loose-fill gets topped up or replaced. Read the label on the original contract and the insulation itself: open-cell foam is soft and sponge-like and runs about 0.5 lb per cubic foot, closed-cell is rigid and runs about 1.4 to 2.0 lb per cubic foot. If there’s no label, we measure depth and density and identify the product on site.

For Icynene specifically, the OEM-versus-aftermarket decision usually favors a compatible equivalent rather than a branded match. Icynene products are proprietary, so a genuine Icynene re-spray means sourcing that exact product line. A quality closed-cell or open-cell equivalent from a listed manufacturer (Owens Corning, Johns Manville, Knauf, Demilec) performs to the same spec when applied by a trained installer, and it may cost less. We source from all of those, so you’re not locked into one brand. We’re an independent contractor, not affiliated with Icynene. We source what your attic actually needs.

Signs Your Icynene Attic Insulation Is Failing

Technician installing blown-in attic insulation with a professional hose
Signs Your Icynene Attic Insulation Is Failing
  • Visible shrinkage or pull-away from the rafters and top plates. This is the classic Icynene failure here. Closed-cell foam can pull back from framing as Henderson attics swing between 40°F winter nights and 150°F summer attic temperatures, opening an air path where the foam used to seal.
  • Sagging on the underside of the roof deck. Open-cell foam can absorb and hold moisture when a roof leak or a poorly vented bathroom fan feeds it. Once saturated it sags, loses R-value fast, and can grow mold on the decking above.
  • R-value that no longer matches the install date. The product spec says R-3.7 per inch for open-cell and R-6 to R-7 per inch for closed-cell. If you measure your depth and the math comes out lower, thermal drift or settling has eaten the difference.
  • A power bill climbing a little each year. When the attic insulation is the only thing aging, that’s the signal. In Henderson, a 15-year-old spray foam job on an unsealed floor loses meaningful R-value to convection currents that run under the foam.
  • Drafty rooms and hot ceilings directly below the attic. This is air movement, not a foam problem by itself: the top plates, can lights, and penetrations weren’t sealed before the foam went down. We see this in Henderson homes more than most, especially on 2015-to-2020 builds where the attic was insulated but the air barrier wasn’t completed.

Replacement Cost & What’s Included

Here’s the line-item range for Henderson attic insulation work, so you can see where your money goes:

Line item Typical installed range
Blown-in loose-fill (Icynene-compatible), full attic $2,400 to $4,200
Open-cell spray foam re-application, full attic $3,200 to $5,600
Closed-cell spray foam re-application, full attic $4,800 to $6,800
Attic air sealing before insulation (top plates, can lights, penetrations) $600 to $1,600
Insulation removal and disposal of failed foam $900 to $2,400
Blower-door test, before and after Included on applicable jobs

What drives the range: attic square footage, how much failed material has to come out, R-value target, and access. What’s included on every job: a written price and written scope before anyone lifts a tool, a Documented Photo Record, and the 365-Day Done Right Promise. On applicable jobs we publish before-and-after blower-door numbers: a pressurization reading that shows, in a single figure, how much conditioned air the home was losing before and after the work.

DIY or Call Us?

Professional contractor installing fiberglass batt insulation in a residential attic
DIY or Call Us?

Some of this you can safely check yourself. Measure insulation depth with a ruler. Look for gaps where foam meets framing. Check your last three summer power bills for the trend. Sniff near the attic hatch. What you should not do: re-spray foam or handle removal yourself. Spray foam chemicals, especially in a closed Henderson attic in July, need respirators, ventilation, and temperature control during cure. Re-application over a failed or saturated layer also traps moisture under the new foam, which is how a small leak becomes roof deck replacement. That’s not a scare tactic, it’s what we find on the jobs we redo.

Under Haven Standard: Arrive on schedule, you get a named technician and a text when they’re on the way. Have it in writing, always. And if you already have a competing estimate, call (844) 320-5338. We’ll read it with you, free, and tell you what’s missing.

Get the price in writing before anything starts.A real person answers, day or night.
Call now

FAQs

Need Insulation help nationwide? Licensed & insured · within the hour response · free estimates
Call (844) 320-5338
Local Service Coverage

Request a Free Estimate in Henderson

Tell us what you need - Envelope Insulation Henderson responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch