A Topside company - serving Henderson, NV

Icynene Home Energy Audit in Henderson, NV

Icynene Home Energy Audit in Henderson: What to Know First

We provide independent Icynene home energy audits in Henderson, typically scheduled within a few days and completed in a single three-to-four-hour visit. You get a blower-door reading before and after air sealing, thermal imaging, a duct leakage test, and an insulation inspection, all documented with photos. Pricing is a written flat number before anyone tests anything, and most audits run between $350 and $650 depending on home size and how many diagnostics you need. This page is for Henderson homeowners who already have Icynene spray foam in the attic, walls, or crawl space and want to know whether it’s performing the way it was sold to perform. Call (844) 320-5338 and a live person answers, day or night.

professional home energy audit service in Henderson, NV

Call (844) 320-5338

How Icynene Products Fail – and How We Fix Them

Icynene is a good product installed correctly. The failures we find in Henderson homes almost always trace back to installation conditions or to what wasn’t done around the foam, not to the chemistry itself. Here are the five patterns we see most.

  • Open-cell foam that pulled away from the attic deck (Icynene Classic Plus and similar open-cell lines). In Henderson’s dry summer heat, attic deck temperatures push past 140°F, and foam sprayed too thin or over a dusty deck can delaminate from the sheathing. You won’t see it from the hatch. We find it with thermal imaging as a warm band where conditioned air is escaping. The fix is re-adhesion after cleaning the substrate, not a fresh topcoat.
  • Off-ratio foam that stayed tacky or crumbly (Icynene ProSeal and medium-density lines). When the A and B drums aren’t at proper temperature, the foam cures soft, with a faint amine smell and a surface that powders under a glove. That foam has almost no R-value per inch and fails an insulation inspection immediately. We core-sample suspect areas, measure density, and remove and re-spray what’s failed.
  • Foam sprayed over an unsealed attic floor. This is the big one. Foam on the roof deck does nothing for the top plates, can lights, and wire penetrations still leaking into the attic. A blower-door test exposes it in one number. We seal those penetrations first, then assess the foam.
  • Closed-cell foam hiding a roof leak (Icynene LD-C-50 and closed-cell lines). Closed-cell is a vapor barrier. When a flashing detail fails above it, water travels along the deck and shows up as a soft, dark patch or a musty pocket at a rafter bay. Thermal imaging flags the wet zone before it becomes rot. We document it and coordinate the roof repair before we touch insulation.
  • Foam in a vented attic that sealed off the soffits. If the installer sprayed over the soffit vents, the attic can’t breathe and moisture builds on the cold deck in winter. We check soffit airflow with a smoke pencil during the audit and correct it with baffles or targeted removal.

As an independent Icynene service provider, we’re not affiliated with or authorized by the manufacturer. That works in your favor: we diagnose what’s actually there, not what a warranty script says should be there.

Our Icynene Home Energy Audit Process

Technician installing blown-in attic insulation with a professional hose
Our Icynene Home Energy Audit Process
  1. 1
    Call and scope. A live person takes the call, we ask what Icynene product you have and when it went in, and we text you a written price and scope before we schedule. No work starts without it.
  2. 2
    Baseline blower-door test. We pressurize the house to 50 pascals and record CFM50, the single figure for how much air your envelope is losing. That number is your starting point.
  3. 3
    Thermal imaging and insulation inspection. An infrared camera walk of the attic, walls, and rim joists shows where the foam is thin, detached, or wet. We photograph each finding.
  4. 4
    Duct leakage test. A duct blaster measures how much of your conditioned air is leaking into the attic or crawl space, which matters in Henderson homes where the air handler often sits in a hot attic.
  5. 5
    Air sealing, then the retest. We seal top plates, can lights, and penetrations, then run the blower door again. Before-and-after readings go in your report so you can see the change you paid for.
  6. 6
    Written report and photo record. You get the numbers, the photos, the scope, and the warranty in writing. If it’s not done right, our 365-Day Done Right Promise covers making it right.

What Icynene Home Energy Audit Costs in Henderson

Home energy audit pricing in Henderson depends on home size, how many diagnostics you need, and whether we find foam that has to be addressed. Here are the ranges we write on estimates.

Service Typical Range
Full home energy audit (blower door, thermal imaging, insulation inspection) $350 – $650
Duct leakage test add-on $150 – $300
Attic air sealing (top plates, can lights, penetrations) $800 – $2,400
Targeted Icynene foam repair or re-spray (small area) $600 – $1,800
Insulation removal and replacement (failed foam, full attic) $2,500 – $6,500

What moves the price: attic square footage, how many penetrations need sealing, whether the foam is open-cell or closed-cell (closed-cell removal costs more), and whether ductwork needs attention. We give you a flat written price before any work starts, and a free second opinion if you’re holding a competing written estimate. Call (844) 320-5338 for your free estimate.

Why Henderson Homeowners Call Envelope Insulation Henderson for Icynene Work

Professional contractor installing fiberglass batt insulation in a residential attic
Why Henderson Homeowners Call Envelope Insulation Henderson for Icynene Work

We’ve sealed and insulated 9,000+ homes since 2016, and every one started with a written price and ended with a documented record. Our technicians have up to 10 years of experience and they know Icynene by sight: open-cell versus closed-cell, a good cure versus an off-ratio one, foam that’s attached versus foam that’s peeling. We source materials from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber, and we also work with Reflectix radiant barrier products, so we’re not locked into one manufacturer’s answer. Calls are answered by a live person 24/7, and you get a Documented Photo Record on every visit, not on request. Bring us a competing estimate and we’ll read it with you, free.

Get the price in writing before anything starts.A real person answers, day or night.
Call now

FAQs

Need Insulation help nationwide? Licensed & insured · within the hour response · free estimates
Call (844) 320-5338
Local Service Coverage

Request a Free Estimate in Henderson

Tell us what you need - Envelope Insulation Henderson responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch