Icynene Wall Insulation in Henderson: What to Know First
We install and repair Icynene wall insulation in Henderson, and most standard wall jobs take one to two days from drill to cleanup. Injection foam into existing cavities is often the fastest path at $2.50 to $4.50 per square foot of wall, while full exterior wall rebuilds run higher. We put a written price in your hands before any work starts, so you know the number before a drill touches your stucco.

This page is for Henderson homeowners who already have Icynene in the walls or are weighing it against open-cell and closed-cell alternatives, and who want to understand how the product actually behaves in our climate before they commit. Our technicians have up to 10 years of experience reading Icynene installs that failed not because the foam was bad, but because the wall assembly around it was never sealed or vented correctly. If you want a straight answer on your specific walls, call (844) 320-5338 and a live person picks up.
How Icynene Products Fail – and How We Fix Them
Icynene is a spray polyurethane foam, and in Henderson it usually fails at the assembly level, not the material level. These are the patterns we actually see, and what we do about each one.
- MD-R-200 and Classic Plus shrinking away from studs. Older open-cell Icynene lines can pull back from framing as they cure and cycle through Henderson’s hot afternoons and cool desert nights. A 1/8-inch gap at the stud face becomes an air channel. We map those pullbacks with a blower-door test and re-seat or top off the foam around each cavity, then seal the top plate where the wall meets the ceiling framing.
- Open-cell foam wicking moisture near the slab. Icynene open-cell is vapor-permeable, which is fine until a wall cavity sits against a slab with no capillary break. In Henderson homes built around the 2015-2018 boom, we routinely find foam that stayed wet at the bottom plate after a monsoon season. The fix isn’t more foam: it’s a vapor barrier and drainage detail before we re-insulate.
- Closed-cell foam that never got full cavity fill. When a previous crew sprayed too fast or too cold, Icynene closed-cell leaves voids and thin spots at the corners. The foam looks solid from the stud bay but the wall leaks. We use a thermal scan to find the voids, then injection-foam those specific cavities rather than tearing out good foam.
- Foam over unsealed penetrations. This is the biggest one. Icynene sprayed over an unsealed top plate, can light, or plumbing penetration traps air behind the foam. We never blow insulation over an unsealed attic floor or wall. Air sealing comes first, then insulation, in that order. On a Henderson job this can change the blower-door number by 30 to 40 percent of what the foam alone would have achieved.
- Bad drill-and-fill measurements from prior work. Injection foam needs the right density and the right hole spacing. When a prior contractor drilled too far apart or under-filled, the cavity ends up with a hollow at the top. We verify fill with an inspection camera at three points per wall before we call the cavity done, and we document it.
We’re an independent Icynene service provider. We aren’t authorized by Icynene and we don’t sell their product as our own; we install and repair it, and we tell you plainly when a different product is the better call.
Our Icynene Wall Insulation Process

- 1
Diagnostics first. We run a blower-door test – a pressurization reading that tells us, in one number, how much air the house is losing through the walls – plus a thermal scan of each exterior wall. You see the numbers and photos before we quote anything.
- 2
Written price and scope. Flat price, written scope, written warranty before anyone lifts a tool. If you have a competing estimate, we’ll read it with you as a free second opinion. No pressure either way.
- 3
Air sealing before insulation. Top plates, penetrations, and any can lights in the wall assembly get sealed first. On a Henderson job, this step usually takes longer than the foam application.
- 4
Parts decision. For repair work we default to OEM Icynene foam when the cavity calls for it, but we’ll tell you when a quality aftermarket injection foam performs the same for less, or when switching to an Owens Corning or Rockwool batt in a specific cavity is the smarter move. No proprietary lock-in.
- 5
The repair or install itself. Drill-and-fill from the exterior where possible to protect your interior finishes, or interior injection-foam access when that’s the cleaner path. Wall soundproofing work on interior partitions uses the same Icynene injection foam at 1.5 to 2.5 lb density.
- 6
Re-test and documentation. Blower-door reading after the work, side by side with the before number. Photos of every cavity, the seal points, and the readings go into your Documented Photo Record, which you get whether you ask or not.
What Icynene Wall Insulation Costs in Henderson
Wall insulation pricing in Henderson depends mostly on access, cavity depth, and whether we’re repairing existing foam or installing fresh. These are the ranges we see in 2026:
| Scenario | Typical range |
|---|---|
| Injection foam into existing wall cavities (drill-and-fill) | $2.50 – $4.50 per sq ft of wall |
| Exterior wall insulation, full rebuild with sheathing and vapor barrier | $4.00 – $7.50 per sq ft |
| Interior wall soundproofing with Icynene injection foam | $1.75 – $3.25 per sq ft |
| Spray foam application to open stud cavities | $1.50 – $3.00 per board foot of foam |
| Air sealing (top plates, penetrations) before foam | $400 – $1,200 per home, typical |
What moves the price: stucco removal and re-stucco on exterior walls, two-story ladder access, foam-density requirements on the west and south walls that see Henderson’s peak summer sun, and whether the cavity has existing foam we need to remove first. A 1,200-square-foot Henderson home with two exterior walls of injection foam typically lands between $3,800 and $6,500 before air sealing. We don’t quote ranges on the phone and call them estimates; you get a written price, and it doesn’t move unless the scope does.
Why Henderson Homeowners Call Envelope Insulation Henderson for Icynene Work

Under The Haven Standard, if the work isn’t done right within 365 days, we make it right. That’s in writing before the crew starts. Our technicians have up to 10 years of experience with Icynene, closed-cell, and open-cell foam, and they know that a Henderson wall built on the west side of the valley needs different density and vapor handling than a north-facing wall on the other side of town. We’ve sealed and insulated over 9,000 homes since 2016, and every one of them has a written price and a documented record when the crew leaves.
We also work with Reflectix radiant barrier and standard vapor barrier products, so if a wall cavity needs a reflective layer rather than foam, we’re not going to sell you the foam. A live person answers at (844) 320-5338, 24/7, no voicemail loop.
FAQs
Not if the repair is done with Icynene-compatible materials and documented properly. Our documented-photo-and-blower-door record is exactly what Icynene’s warranty process expects. We’re an independent Icynene service provider and we’ll be honest with you upfront if a repair falls outside what the manufacturer would cover, rather than after the fact.
Icynene foam components are available through regional supply in Las Vegas and Henderson on normal lead times, usually two to four business days for a standard two-component kit. For most residential wall jobs, we don’t wait on supply; the bottleneck is access and diagnostics, not material.
Repair is almost always cheaper when the foam itself is still good and the failure is at the studs or top plate. A targeted injection-foam repair on a 60-square-foot failing section runs $150 to $400; a full replacement of that wall runs four to five times that. We only recommend replacement when the foam has been wet for multiple seasons or has outright delaminated.
Diagnostics usually happen within two to four business days of your call, and the wall work itself typically starts the same week. Emergency repairs (water intrusion behind the foam, a wall that’s actively leaking) get moved up. Call (844) 320-5338 and a live person will schedule you on the call.
Yes, but not by spraying foam over the batts. We remove the existing fiberglass in the affected cavities first, then air seal, then install Icynene or a batt that’s spec’d for the cavity. Spraying over old batts traps the same air leaks Icynene is supposed to eliminate. That removal work is baked into the written price, not tacked on after.
Call (844) 320-5338 for a free estimate on your Icynene wall insulation in Henderson. A written price goes in your hands before any work starts, and a live person answers 24/7.
Written by the team at Envelope Insulation Henderson, serving Henderson and nearby areas.