Knauf Home Energy Audit in Henderson: What to Know First
An independent Knauf home energy audit in Henderson typically runs 2 to 4 hours on site, and you leave with a written report: blower-door readings in CFM50, thermal images, and a flat price for any work we recommend. We’re upfront about the posture here. The audit itself is a real diagnostic, not a sales pitch dressed up as one, and any work that follows gets a written price before anyone touches your attic. We’re an independent Knauf service provider, not affiliated with or authorized by the manufacturer.

This page is for Henderson homeowners who already have Knauf insulation in the walls or attic, or who are weighing it, and want to know what an audit will actually measure in a home built or retrofitted in this climate. Our technicians have up to 10 years of experience with fiberglass batts and blown products, and we carry Knauf alongside Owens Corning, Johns Manville, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber, so no product lock-in. Call (844) 320-5338 and a live person answers.
How Knauf Products Fail – and How We Fix Them
Knauf makes solid fiberglass, and most of what we find wrong in Henderson attics isn’t the product failing on its own. It’s installation and envelope problems that the product can’t fix by itself. Here’s what our audits turn up, series by series.
- Knauf EcoBatt batts compressed at the eaves. In Henderson’s low-slope 1990s and 2000s attics, installers routinely stuff full-thickness batts into the tight wedge where the roof meets the top plate. Compressed fiberglass loses R-value fast, and that corner is where our thermal camera reads the coldest in winter. We measure the compressed depth, calculate the actual R-value lost, and correct the coverage with a baffle and blown fill rather than another batt jammed in the same spot.
- Knauf Jet Stream blown fiberglass with no air seal underneath. This is the big one. Blown fiberglass over an unsealed attic floor looks fine and performs poorly, because air moves through it freely. Our blower-door test tells the story in one number. We’ve pulled Jet Stream back, sealed the top plates, can lights, and wire penetrations, then re-blew to the target depth and re-tested. The before-and-after readings are published on the job.
- Knauf batts sagging in wall cavities after a moisture event. Henderson’s summer monsoon pushes humid air against exterior walls, and a small roof or window leak wets fiberglass that then sags and leaves an uninsulated gap at the top of the cavity. The audit’s thermal scan on a hot afternoon makes those voids glow. We remove the wet batts, dry and treat the cavity, and reinstall.
- Knauf duct wrap that’s been crushed or taped over. Duct leakage testing on Henderson homes with attic ducts often finds the wrap compressed at hangers or joints taped with the wrong product, letting attic heat load the duct. We measure leakage before and after taping and mastic sealing the actual leak points, not just the visible joints.
- Knauf products mixed with older, unknown insulation. In remodels we find Knauf batts laid over decades-old material of unknown origin. We identify what’s there, and if it’s compromised or wet, our removal and replacement service pulls it before new product goes down. Blowing over it is how good Knauf product ends up doing nothing.
Our Knauf Home Energy Audit Process

- 1
Call and schedule. A live person answers, we confirm the home’s age and what you know about the existing Knauf product, and you get a named technician and a text when they’re on the way.
- 2
Diagnostics. We run a blower-door test (a pressurization reading that shows, in one number, how much air the building envelope is losing) and a thermal imaging inspection, plus an insulation inspection in the attic and walls. On homes with attic ducts, we add a duct leakage test.
- 3
Written findings and price. You get the readings, the photos, and a flat price for any recommended work, in writing, before anything starts. Haven Standard Clause 1.
- 4
The repair, sealed first. If insulation is the fix, we air seal before we add product. We never blow over an unsealed attic floor. OEM Knauf replacement product where it’s the right call; quality aftermarket where it performs the same or better for less.
- 5
Re-test. We repeat the blower-door test and publish the before-and-after CFM50 numbers so you can see the change you paid for.
- 6
Documented record and cleanup. A full photo record is included on every visit, not on request. The 365-Day Done Right Promise applies: if it’s not done right, we make it right.
What Knauf Home Energy Audit Costs in Henderson
Here’s what typical Henderson jobs run. Every figure is a range, and your written price is flat once we’ve measured.
- Full home energy audit (blower door, thermal imaging, insulation inspection): $450-$850 depending on square footage and whether ducts are tested.
- Attic air sealing before re-insulating: $1,200-$2,800, driven by can-light count and attic complexity.
- Blown fiberglass top-up or replacement (Knauf Jet Stream or equivalent): $1,800-$4,200, driven by attic square footage and target R-value.
- Duct leakage test and sealing: $600-$1,500.
What moves the price: attic access, existing insulation that needs removal, the number of penetrations to seal, and whether the home has a second story over a hot garage. Bring us a competing written estimate and we’ll read it with you, free. Estimates are free and there’s a written price before any work starts.
Why Henderson Homeowners Call Envelope Insulation Henderson for Knauf Work

We’ve completed work on more than 9,000 homes since 2016, and every one started with a written price and ended with a documented photo record. That record includes before-and-after blower-door readings on jobs where air sealing is part of the scope, so the result is a number, not a claim. Our technicians are background-checked and uniformed, and they know Knauf batts and blown product well enough to tell you when re-blowing is the fix and when it isn’t. We work with Reflectix and the other brands listed above whenever a different product is the better answer; the brand on the bag is your call, the envelope performance is ours. Calls are answered 24/7 by a live person. The 365-Day Done Right Promise backs every completed job.
FAQs
Does an energy audit affect my Knauf product warranty? No. The audit is a diagnostic and doesn’t alter the installed product, so it doesn’t affect Knauf’s warranty. Where we do repair or replacement work, we install according to manufacturer instructions and document the installation with photos, which keeps the record intact.
Can you match my existing Knauf product for a top-up? Usually, yes. We identify the Knauf line already in the attic and match R-value and thickness, or explain in writing why a different product performs better. We never guess by eyeballing color alone.
Is it cheaper to repair or replace Knauf insulation? Repair, if the product is dry and intact and the problem is air leakage underneath it. Replace, if it’s compressed beyond recovery, water-damaged, or mixed with unknown older material. The blower-door test and thermal scan tell us which, and the written report shows you why.
How fast can you get out for an audit in Henderson? Most audits are scheduled within a few days, and same-day emergency availability covers urgent cases. Call (844) 320-5338 for the soonest slot.
Will I get the actual blower-door numbers? Yes. On applicable jobs the before-and-after CFM50 readings are given to you and published on the job record. Call (844) 320-5338 for a free estimate.
Get Your Knauf Energy Audit Scheduled

If you’ve got Knauf in the attic and you’re not sure it’s doing its job, an audit gives you the numbers to know. Call Envelope Insulation Henderson at (844) 320-5338 for a free estimate, and a live person will help you get scheduled. Written price before any work starts, documented photo record on every visit, and the 365-Day Done Right Promise behind it.
Written by the team at Envelope Insulation Henderson, serving Henderson and nearby areas.