Rockwool Home Energy Audit in Henderson: What to Know First
We provide independent Rockwool home energy audit service in Henderson, and most audits are completed in a single three-to-four hour visit, with the written report and before-and-after blower-door numbers delivered the same week. Pricing is flat and written before any work starts: a standalone audit runs $400 to $850 depending on home size and how many diagnostic tests you need. We’re not affiliated with or authorized by Rockwool; we’re an independent Rockwool service provider, which means we read your home’s numbers honestly and recommend what the measurements support.

This page is for Henderson homeowners who already have Rockwool insulation or mineral wool products in the envelope and want to know whether they’re performing, whether air sealing was ever done properly, and what it will cost to fix. Call (844) 320-5338 and a live person answers, day or night.
How Rockwool Products Fail – and How We Fix Them
Rockwool is dense, moisture-resistant, and fire-stable, so it tends to fail differently than fiberglass batt or loose-fill cellulose. The insulation itself rarely “wears out.” What fails is the installation around it and the air barrier underneath it. Five patterns show up again and again on Henderson audits:
- Comfortbatt batts compressed at the eaves. In Henderson’s low-slope 1990s attics, the roof line pinches down near the soffit and installers fold or crush the batt to fit. Rockwool Comfortbatt loses R-value fast when compressed – a batt rated R-15 can perform closer to R-11 once squashed to 3 inches. We find it with thermal imaging, then reset the depth or switch to a thinner high-density product in that zone.
- Safe’n’Sound in interior walls doing nothing for the envelope. This is a sound batt, not a thermal one. We regularly find it installed in exterior walls of Henderson homes where a thermal product belonged. The audit catches it because the wall assembly reads cold on the thermal camera despite full cavity fill. Our fix is to flag it in the report and price the swap only if the wall is already open.
- Rockwool blown-in settling away from the top plate. Loose mineral wool settles over the first two heating seasons, and because it doesn’t friction-fit like a batt, it drifts off the top plate and leaves the exact gap air sealing is supposed to close. The blower-door test reads that gap. We re-level the depth and seal the plate before adding anything.
- Mineral wool installed over an unsealed attic floor. This is the big one. Dense Rockwool hides air leaks from can lights, plumbing penetrations, and top plates the way a rug hides a stain. The audit’s before-reading exposes it. Under The Haven Standard, we seal first, then insulate – we never blow insulation over an unsealed floor, and we’ll say so plainly if that’s what we find.
- Vapor barrier mistakes at the crawl space interface. Rockwool tolerates moisture better than most products, which tempts installers to skip proper vapor management in Henderson’s monsoon-season humidity. We inspect the crawl space and rim joist separately, because a dry-looking attic can sit above a wet foundation.
Our Rockwool Home Energy Audit Process

- 1
Intake call and schedule. You get a named technician and a text when they’re on the way. No voicemail loops.
- 2
Blower-door test. A pressurization reading, in CFM50, that shows in one number how much air your building envelope is losing. This is your “before.”
- 3
Thermal imaging and insulation inspection. We walk the attic, walls, and crawl space with the camera, documenting gaps, compression, and missed air sealing. Every finding gets a photo.
- 4
Duct leakage test where applicable. Henderson’s duct runs through hot attics leak conditioned air into the worst possible place. We measure it rather than guess.
- 5
Written report and price. A flat written scope, a written warranty, and the diagnostic numbers, delivered before anyone lifts a tool. If you have a competing estimate, we’ll read it with you as a free second opinion.
- 6
Documented close. The 365-Day Done Right Promise applies to all completed work, and you keep the photo record and the after-reading.
What Rockwool Home Energy Audit Costs in Henderson
Flat pricing, written before work starts. Here’s what the common scenarios run:
| Service | Typical Range |
|---|---|
| Standalone home energy audit (blower door, thermal imaging, insulation inspection, written report) | $400 – $850 |
| Audit plus duct leakage test | $550 – $1,050 |
| Attic air sealing (top plates, can lights, penetrations) before re-insulating | $900 – $1,800 |
| Re-leveling or correcting compressed Rockwool batts in a standard attic | $700 – $1,600 |
| Crawl space vapor barrier correction | $1,200 – $3,200 |
What moves the price: attic square footage, how many air-sealing points we find, duct accessibility, and whether the existing Rockwool can be corrected in place or has to come out. The audit itself absorbs into repair pricing if you proceed – ask us how. Call (844) 320-5338 for a written price; estimates are free.
Why Henderson Homeowners Call Envelope Insulation Henderson for Rockwool Work

We’ve sealed and insulated 9,000+ homes under The Haven Standard since 2016, and not one of them started without a written price and a written warranty in hand. Our technicians have up to 10 years of experience, and they know the difference between Comfortbatt and Safe’n’Sound without being told. Every visit includes a Documented Photo Record – not on request, on every job – so you can see the before and after yourself. We also service Reflectix and other products, so we’re not pushing one brand. The 365-Day Done Right Promise: if it’s not done right, we make it right. Calls are answered by a live person 24/7, and you get a text when the tech is on the way.
FAQs
No. Properly installed Rockwool mineral wool doesn’t lose its warranty because the air barrier around it was sealed. The opposite is true: air sealing protects the product from moisture and condensation, which is what actually causes problems. We document the installed condition photographically so the record is clear if you ever need to file a claim.
Usually, yes, in a single visit. Compression, top-plate gaps, and improper depth all read clearly under thermal imaging combined with the blower-door test. In Henderson’s low-slope attics the compression issues are the most common thing we find, and we flag them in the written report before quoting a fix.
Repair almost always wins. Rockwool isn’t the thing that failed – the air sealing underneath it did. Unless the material is water-damaged or installed in the wrong assembly entirely, correcting the seal and re-leveling the depth gets you most of the performance back for a fraction of full replacement. Our audit tells you which side of that line your Henderson home is on.
Audits are typically scheduled within a few business days, and a live person answers your call 24/7 to book it. The audit itself takes three to four hours, and the written report arrives that week. Call (844) 320-5338 for a written price.
Yes. We source from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber, and we also handle Reflectix. No product lock-in – the diagnostic numbers decide what gets recommended.
Written by the team at Envelope Insulation Henderson, serving Henderson and nearby areas.